The Octopus Chippa Wilson Pin Tail Signature Traction Pad is built for surfers riding pulled-in tails who want maximum grip without adding unnecessary bulk underfoot. Designed specifically for pin tails and narrow tail blocks, this 4-piece pad uses Octopus' low-profile Corduroy Grip™ pattern to deliver a direct, tactile connection to the board while keeping your back foot secure through fast, critical surfing.
Designed for Pin Tails and Narrow Tail Blocks
Unlike wider traction pads that can overwhelm a narrow tail, the Chippa Pin is shaped to better follow the pulled-in outline of step-ups and pin-tail performance boards. Its 4-piece customizable layout lets you spread the sections to match your board's tail shape, helping you get full coverage where you need it without forcing a bulky pad onto a narrow template.
Key Features
- 4-piece customizable design: Lets you adjust spacing to follow narrow and pulled-in tail outlines.
- Optimized for pin tails: Specifically designed for step-ups and boards with narrower tail blocks.
- Corduroy Grip™ pattern: Low-profile grooves provide a highly tactile feel without excessive padding.
- Flat arch: Keeps the pad low and unobtrusive for surfers who prefer direct board feel.
- 3M high-grade adhesive: Secure peel-and-stick backing for dependable attachment when properly installed.
Chippa Pin Traction Pad Specs
- Overall size: 12.5" wide x 14.5" high
- Layout: 4-piece customizable split pad
- Compatibility: Pin tails and narrow tail blocks
- Grip pattern: Corduroy Grip™
- Arch: Flat
- Adhesive: 3M high-grade secure stick
Low-Profile Grip for a More Direct Feel
The Corduroy Grip™ pattern is designed for surfers who want traction without a thick or overly cushioned feel. The low-profile surface helps preserve sensitivity under your rear foot, making it easier to feel subtle changes in pressure and board response while still giving you the grip needed for committed turns.
Who Is the Chippa Wilson Pin Tail Pad Best For?
This pad is a strong choice for surfers riding step-ups, pin tails, and performance boards with narrow tail blocks. If a conventional traction pad feels too wide, too bulky, or doesn't follow the outline of your tail cleanly, the Chippa Pin's 4-piece design gives you much more control over placement.
How to Install the Chippa Pin Traction Pad
Start with a completely clean, dry, and wax-free deck. Before removing the adhesive backing, lay out all four pieces and adjust the spacing so the pad follows the tail outline naturally. Once you're satisfied with the position, peel the backing, press each section firmly into place, and make sure all edges are fully bonded to the deck.
Rider Shack Note
Buying your Octopus Chippa Wilson Pin Tail Traction Pad from Rider Shack supports a small business and core surf shop run by surfers. We're here to help you match your traction setup to your board so your gear works the way you want it to in the water.
FAQ: Octopus Chippa Wilson Pin Tail Traction Pad
How many pieces does the Chippa Pin traction pad have?
It uses a 4-piece customizable layout, allowing you to adjust the spacing to better follow a narrow or pulled-in tail shape.
What type of surfboard is this traction pad designed for?
The Chippa Pin is specifically designed for pin tails, narrow tail blocks, and step-up surfboards.
Does the Chippa Pin have a center arch?
No. This pad uses a flat arch, making it a good choice for surfers who prefer a lower-profile feel underfoot.
What is Corduroy Grip™?
Corduroy Grip™ is Octopus' low-profile traction pattern designed to provide a tactile, direct connection to the board without adding unnecessary thickness.
How large is the Octopus Chippa Pin traction pad?
The complete pad measures approximately 12.5" wide x 14.5" high.
What adhesive does the Chippa Pin use?
It uses 3M high-grade secure-stick adhesive. Proper deck preparation is important for the strongest and longest-lasting bond.
