Just like the name says this Lost surfboard is a bottom feeder it loves the slop surf. This surfboard is a tri-plane hull that catches the smallest of ripple and allows you to turn without losing speed.

Lost Bottom Feeder Details"
5'8 x 21.5" x 2.5"
32.12 Cubic Litres
Futures 5 fin Setup
Knee-Head High Waves Learn More

This 5'6 Lost rocket surfboard is a surfboard classic. This surfboard has a winged diamond tail so it will hold in bigger surf but still catch the waves with ease.

Lost Rocket Details:
5'4 x 18.75" x 2.25"
24.18 cubic Litres
FCS 5 Fin
2-6' Surf Learn More

The Lost Lay-Z boy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
6' x 22" x 2.75"
41.74 cubic litres
Future 5 fin set up
Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'2 x 20.5" x 2.75"
35.86 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'6 x 21.5" x 2.88"
39.35 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'4 x 21" x 2.75"
37.65 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf. This surfboard was resin tinted by the Lucky Bastards so it is very unique and a 1 off. Please not this board has a small imperfection in the Lost logo under the glass.

Lost Couch Potato details:

5'6 x 21.5" x 2.38"
33.1 Cubic Litres
Futures 5 fin set up
1-4 foot surf
Learn More

TheLost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling in mushy surf.

Lost Rocket V2 stub Details:

• 5'7 x 19.75" x 2.25"li>
  
• 28.42 Cubic Litres


• Future Fins


• EPS Epoxy


• 2-6' Surf

Learn More

TheLost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling in mushy surf.

Lost Rocket V2 stub Details:

• 5'9 x 20.25" x 2.32"


• 31.03 Cubic Litres


• Future Fins


• EPS Epoxy


• 2-6' Surf

Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'5 x 20.25" x 2.35"
29.2 cubic litres
FCS 5 fin set up
Keahana Epoxy Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

5'6 x 21.5" x 2.38"
33.31 Cubic Litres
FCS 5 fin set up
1-4 foot surf Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

5'4 x 21" x 2.32"
30.63 Cubic Litres
FCS 5 fin set up
1-4 foot surf Learn More

This 5'6 Lost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling is mushy surf.

Lost Rocket V2 Details:

• 5'6 x 19.5" x 2.25"


• 27.53 Cubic Litres


• Future Fins


• Keahana Epoxy


• 2-6' Surf

Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

5'6 x 21.5" x 2.38"
33.3 Cubic Litres
Futures 5 fin set up
1-4 foot surf
Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
6'0 x 21.25" x 2.56"
38.54 cubic litres
Future 5 fin set up
Epoxy Construction with Bamboo Deck Learn More

The Lost Lay-Z boy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'11 x 21.75 x 2.69
39.52 cubic litres
Future 5 fin set up
Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'10 x 21.20 x 2.63
39.25 cubic litres
Future 5 fin set up Learn More

Lost 5'11 Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 5'11 x 20.75 x 2.5


• Future 5-Fin


• 34.42 Cubic Liters

Learn More

Lost 6' Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 6' x 21" x 2.56"


• FCS 5-Fin


• 36.12 Cubic Liters

Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.



Lost Pelagic Surfboard Details:





5'7 x 19.75" x 2.38"


Future 5-Fin


29.09 Cubic Liters Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'9 x 19.25" x 2.32"

27.15 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'8 x 19" x 2.32"

26.30 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'10 x 19.5" x 2.38"

28.42 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'8 x 22 x 2.32

36.90 Cubic Litres

FCS 5 fin set up

1-4 foot surf Learn More

The Lost Sub Scorcher 2 surfboard is a fresh twist on the extremely popular Sub Scorcher model. The Vee bottom was removed from the last 6" of the tail which increases the rocker by about a 1/4" still keeping the rail line static. As a result the board surfs looser for better vertical and pocket surfing. To keep the board fast with losts of drive Lost straightened the outline in the tail by adding the double wing swallow tail. This is a great everyman's daily average wave shortboard.

THIS SURFBOARD WAS A RETURN. It has been surfed 1 x and has 2 very minor pressure dents on the deck. The price has been dropped. This board also comes with a Astrodeck black traction pad.

Lost Sub Scorcher 2 Details:

6'0x 19.75 x 2.50


32.45 Cubic Litres


Future 5 Fin Setup


2-5 foot surf

Learn More

The Lost Sub Scorcher 2 surfboard is a fresh twist on the extremely popular Sub Scorcher model. The Vee bottom was removed from the last 6" of the tail which increases the rocker by about a 1/4" still keeping the rail line static. As a result the board surfs looser for better vertical and pocket surfing. To keep the board fast with losts of drive Lost straightened the outline in the tail by adding the double wing swallow tail. This is a great everyman's daily average wave shortboard.



Lost Sub Scorcher 2 Details:

5'10 x 19.25 x 2.38


29.19 Cubic Litres


FCS 5 fin setup

2-5 foot surf

Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'6 x 21" x 2.32"

30.63 Cubic Litres

FCS/5

1-4 foot surf Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Lost Pelagic Surfboard Details:


6'1 x 21.25" x 2.63"

FCS 5-Fin

37.13 Cubic Liters Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'10 x 22.5" x 2.63"

39.14 Cubic Litres

Future Fins

1-4 foot surf Learn More

The world's all-time best selling fish model surfboard. During the filming of 5'5" REDUX, the RNF and RNF Quad were updated and fine tuned. The nose has gotten wider again, and more conservative overall rocker and less concave make for a board that will hold speed in flats and produce harder, longer carves.

A longer, less pronounced vee in the tail gives a more predictable feel out of turns, and a straighter outline adds drive and hold. The deep wing, influenced by MR's vintage twin fins, adds more control of high speeds and better bite in snaps and out of carves. It still paddles great, still makes you look good, but the updates allow harder, more powerful carving turns and a wider range of performance in more varied surf.

Enjoy playing with a multitude of fin setups. The RNF is designed as a twin with rear trailer, but works great as a pure twin fin or try all three standard thrusters for different feels in different conditions. ...Everyone should own one.

Lost Round Nose Fish Surfboard Details:

• 5'11 x 20" x 2.42"


• 33.77 Cubic Litres


• Future 5 Fin


• Wave Height 1-6'

Learn More

This 6' Lost rocket surfboard is just like original but with some new minor details. This surfboard has a winged diamond tail so it will hold in bigger surf but still catch the waves with ease. This board is constructed with Etech technology.

Lost Rocket V2 Details:

• 5'10 x 20.25" x 2.38"


• 32.04 Cubic Litres


• Futures 5-Fin


• Epoxy Construction with Bamboo Deck


• 2-6' Surf

Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Lost Pelagic Surfboard Details:

• 5'8 x 20" x 2.38"


• FCS 5-Fin


• 29.94 Cubic Liters

Learn More

Lost 5'11 Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 5'11 x 20.75 x 2.5


• FCS 5-Fin


• 34.42 Cubic Liters

Learn More

This Faction 5'8 White Pony Surfboard is the ultimate small wave board. Its width and thickness helps with paddling and gliding through flat sections.

Details:
5'8 x 21 x 2.75
Future 5-Fin
2 to 4ft Waves
Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 5'10 x 19.25 x 2 3/8"


• 27.68 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 5'8 x 19 x 2.25"


• 25.15 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 5'6 x 18.75 x 2 1/8"


• 22.9 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'0 x 19.5 x 2.5"


• 30.36 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'6 x 20.5 x 2.75"


• 37.88 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'4 x 20.25 x 2 5/8"


• 34.88 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'2 x 19.75 x 2.5"


• 31.89 Cubic Litres


• Future Fins

Learn More

The Super Fish II has been updated for 2012 making one of the most popular boards even better. The idea behind the Super Fish design is to offer a board that rides, paddles and catches waves easily regardless of your ability.

The generous outline and smooth rocker makes this board incredibly easy to ride. One of the most notable features of the Super Fish design is the step deck. This gives the board greater buoyancy while maintaining a performance rail profile making the board sensitive and easier to turn.

The new bottom contour features a deep single-to-double concave providing greater speed and acceleration. The tail wings are now more defined creating bite off the bottom and quicker release through turns. The swallowtail is also shallower than before. This adds surface area under your back foot meaning more speed in flatter waves.

FCS plugs are set up in a tri-quad configuration so you can ride it as a thruster or a quad, and our X2 Epoxy technology uses a multi-layered sandwich process that produces a light yet incredibly durable surfboard that’s ideal for travel.

If you're looking for a high volume, easy to ride surfboard that'll increase your wave count then the Super Fish II is the board for you.

7S Super Fish II Surfboard Details:

• 5'9 x 20 x 2.25"


• 25.9 Cubic Litres


• FCS Fins (quad Set included)


• Waist to head high surf

Learn More

The Super Fish II has been updated for 2012 making one of the most popular boards even better. The idea behind the Super Fish design is to offer a board that rides, paddles and catches waves easily regardless of your ability.

The generous outline and smooth rocker makes this board incredibly easy to ride. One of the most notable features of the Super Fish design is the step deck. This gives the board greater buoyancy while maintaining a performance rail profile making the board sensitive and easier to turn.

The new bottom contour features a deep single-to-double concave providing greater speed and acceleration. The tail wings are now more defined creating bite off the bottom and quicker release through turns. The swallowtail is also shallower than before. This adds surface area under your back foot meaning more speed in flatter waves.

FCS plugs are set up in a tri-quad configuration so you can ride it as a thruster or a quad, and our X2 Epoxy technology uses a multi-layered sandwich process that produces a light yet incredibly durable surfboard that’s ideal for travel.

If you're looking for a high volume, easy to ride surfboard that'll increase your wave count then the Super Fish II is the board for you.

7S Super Fish II Surfboard Details:

• 8'0 x 23 x 3"


• 66.9 Cubic Litres


• FCS Fins (quad Set included)


• Waist to head high surf

Learn More

The Super Fish II has been updated for 2012 making one of the most popular boards even better. The idea behind the Super Fish design is to offer a board that rides, paddles and catches waves easily regardless of your ability.

The generous outline and smooth rocker makes this board incredibly easy to ride. One of the most notable features of the Super Fish design is the step deck. This gives the board greater buoyancy while maintaining a performance rail profile making the board sensitive and easier to turn.

The new bottom contour features a deep single-to-double concave providing greater speed and acceleration. The tail wings are now more defined creating bite off the bottom and quicker release through turns. The swallowtail is also shallower than before. This adds surface area under your back foot meaning more speed in flatter waves.

FCS plugs are set up in a tri-quad configuration so you can ride it as a thruster or a quad, and our X2 Epoxy technology uses a multi-layered sandwich process that produces a light yet incredibly durable surfboard that’s ideal for travel.

If you're looking for a high volume, easy to ride surfboard that'll increase your wave count then the Super Fish II is the board for you.

7S Super Fish II Surfboard Details:

• 6' x 20.25" x 2 7/16"


• 33.3 Cubic Litres


• FCS Fins (quad Set included)


• Waist to head high surf

Learn More

The Super Fish II has been updated for 2012 making one of the most popular boards even better. The idea behind the Super Fish design is to offer a board that rides, paddles and catches waves easily regardless of your ability.

The generous outline and smooth rocker makes this board incredibly easy to ride. One of the most notable features of the Super Fish design is the step deck. This gives the board greater buoyancy while maintaining a performance rail profile making the board sensitive and easier to turn.

The new bottom contour features a deep single-to-double concave providing greater speed and acceleration. The tail wings are now more defined creating bite off the bottom and quicker release through turns. The swallowtail is also shallower than before. This adds surface area under your back foot meaning more speed in flatter waves.

FCS plugs are set up in a tri-quad configuration so you can ride it as a thruster or a quad, and our X2 Epoxy technology uses a multi-layered sandwich process that produces a light yet incredibly durable surfboard that’s ideal for travel.

If you're looking for a high volume, easy to ride surfboard that'll increase your wave count then the Super Fish II is the board for you.

7S Super Fish II Surfboard Details:

• 6'3 x 20.5" x 2.5"


• 36.2 Cubic Litres


• FCS Fins (quad Set included)


• Waist to head high surf

Learn More

This 5'6 Lost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling is mushy surf.

Lost Rocket V2 Details:

• 5'6 x 19.75" x 2.25"


• 27.51 Cubic Litres


• FCS Fins


• 2-6' Surf

Learn More

This Lost Rocket is a great board for small mushy surf the Lost Rocket is the orginator of the high performance slop surfer.

Lost Rocket Details:

• 5'6 x 19" x 2.18


• Future Fins


• 24.90 Cubic Litres


• Knee to head high surf

Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

• 5'8 x 22" x 2.5"


• 36.7 Cubic Litres


• FCS Fins


• 1-4 foot surf

Learn More

Just like the name says this Lost surfboard is a bottom feeder it loves the slop surf. This surfboard is a tri-plane hull that catches the smallest of ripple and allows you to turn without losing speed.

Lost Bottom Feeder Details:

• 6' x 22.5"" x 2.75"


• 42.49 Cubic Litres


• Futures 5 fin Setup


• Knee-Head High Waves

Learn More