Just like the name says this Lost surfboard is a bottom feeder it loves the slop surf. This surfboard is a tri-plane hull that catches the smallest of ripple and allows you to turn without losing speed.

Lost Bottom Feeder Details"
5'8 x 21.5" x 2.5"
32.12 Cubic Litres
Futures 5 fin Setup
Knee-Head High Waves Learn More

This 5'6 Lost rocket surfboard is a surfboard classic. This surfboard has a winged diamond tail so it will hold in bigger surf but still catch the waves with ease.

Lost Rocket Details:
5'4 x 18.75" x 2.25"
24.18 cubic Litres
FCS 5 Fin
2-6' Surf Learn More

The Lost Lay-Z boy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
6' x 22" x 2.75"
41.74 cubic litres
Future 5 fin set up
Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'2 x 20.5" x 2.75"
35.86 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'6 x 21.5" x 2.88"
39.35 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'4 x 21" x 2.75"
37.65 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'5 x 20.25" x 2.35"
29.2 cubic litres
FCS 5 fin set up
Keahana Epoxy Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

5'6 x 21.5" x 2.38"
33.31 Cubic Litres
FCS 5 fin set up
1-4 foot surf Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

5'4 x 21" x 2.32"
30.63 Cubic Litres
FCS 5 fin set up
1-4 foot surf Learn More

This 5'6 Lost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling is mushy surf.

Lost Rocket V2 Details:

• 5'6 x 19.5" x 2.25"


• 27.53 Cubic Litres


• Future Fins


• Keahana Epoxy


• 2-6' Surf

Learn More

The Lost Lay-Z boy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'11 x 21.75 x 2.69
39.52 cubic litres
Future 5 fin set up
Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
5'10 x 21.20 x 2.63
39.25 cubic litres
Future 5 fin set up Learn More

Lost 5'11 Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 5'11 x 20.75 x 2.5


• Future 5-Fin


• 34.42 Cubic Liters

Learn More

Lost 6' Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 6' x 21" x 2.56"


• FCS 5-Fin


• 36.12 Cubic Liters

Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.



Lost Pelagic Surfboard Details:





5'7 x 19.75" x 2.38"


Future 5-Fin


29.09 Cubic Liters Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'9 x 19.25" x 2.32"

27.15 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'8 x 19" x 2.32"

26.30 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:


5'10 x 19.5" x 2.38"

28.42 Cubic Liters

FCS Fins/5 fin setup

3-7 foot surf Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'8 x 22 x 2.32

36.90 Cubic Litres

FCS 5 fin set up

1-4 foot surf Learn More

The Lost Sub Scorcher 2 surfboard is a fresh twist on the extremely popular Sub Scorcher model. The Vee bottom was removed from the last 6" of the tail which increases the rocker by about a 1/4" still keeping the rail line static. As a result the board surfs looser for better vertical and pocket surfing. To keep the board fast with losts of drive Lost straightened the outline in the tail by adding the double wing swallow tail. This is a great everyman's daily average wave shortboard.

THIS SURFBOARD WAS A RETURN. It has been surfed 1 x and has 2 very minor pressure dents on the deck. The price has been dropped. This board also comes with a Astrodeck black traction pad.

Lost Sub Scorcher 2 Details:

6'0x 19.75 x 2.50


32.45 Cubic Litres


Future 5 Fin Setup


2-5 foot surf

Learn More

The Lost Sub Scorcher 2 surfboard is a fresh twist on the extremely popular Sub Scorcher model. The Vee bottom was removed from the last 6" of the tail which increases the rocker by about a 1/4" still keeping the rail line static. As a result the board surfs looser for better vertical and pocket surfing. To keep the board fast with losts of drive Lost straightened the outline in the tail by adding the double wing swallow tail. This is a great everyman's daily average wave shortboard.



Lost Sub Scorcher 2 Details:

5'10 x 19.25 x 2.38


29.19 Cubic Litres


FCS 5 fin setup

2-5 foot surf

Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'6 x 21" x 2.32"

30.63 Cubic Litres

FCS/5

1-4 foot surf Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Lost Pelagic Surfboard Details:


6'1 x 21.25" x 2.63"

FCS 5-Fin

37.13 Cubic Liters Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:


5'10 x 22.5" x 2.63"

39.14 Cubic Litres

Future Fins

1-4 foot surf Learn More

The world's all-time best selling fish model surfboard. During the filming of 5'5" REDUX, the RNF and RNF Quad were updated and fine tuned. The nose has gotten wider again, and more conservative overall rocker and less concave make for a board that will hold speed in flats and produce harder, longer carves.

A longer, less pronounced vee in the tail gives a more predictable feel out of turns, and a straighter outline adds drive and hold. The deep wing, influenced by MR's vintage twin fins, adds more control of high speeds and better bite in snaps and out of carves. It still paddles great, still makes you look good, but the updates allow harder, more powerful carving turns and a wider range of performance in more varied surf.

Enjoy playing with a multitude of fin setups. The RNF is designed as a twin with rear trailer, but works great as a pure twin fin or try all three standard thrusters for different feels in different conditions. ...Everyone should own one.

Lost Round Nose Fish Surfboard Details:

• 5'11 x 20" x 2.42"


• 33.77 Cubic Litres


• Future 5 Fin


• Wave Height 1-6'

Learn More

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Lost Pelagic Surfboard Details:

• 5'8 x 20" x 2.38"


• FCS 5-Fin


• 29.94 Cubic Liters

Learn More

Lost 5'11 Pelagic Fish Surfboard:

In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Details:

• 5'11 x 20.75 x 2.5


• FCS 5-Fin


• 34.42 Cubic Liters

Learn More

This Faction 5'8 White Pony Surfboard is the ultimate small wave board. Its width and thickness helps with paddling and gliding through flat sections.

Details:
5'8 x 21 x 2.75
Future 5-Fin
2 to 4ft Waves
Learn More

This 5'6 Lost rocket V2 Stub surfboard is just like the V2 but with some new minor details. This surfboard has a fuller outline and volume for extreme groveling is mushy surf.

Lost Rocket V2 Details:

• 5'6 x 19.75" x 2.25"


• 27.51 Cubic Litres


• FCS Fins


• 2-6' Surf

Learn More

This Lost Rocket is a great board for small mushy surf the Lost Rocket is the orginator of the high performance slop surfer.

Lost Rocket Details:

• 5'6 x 19" x 2.18


• Future Fins


• 24.90 Cubic Litres


• Knee to head high surf

Learn More

The Lost Couch Potato surfboard is the extreme small wave surfboard. It is wider, shorter, and has a really flat rocker. The outline and the rocker of this board make it extremely fast, yet very controllable in gutless surf.

Lost Couch Potato details:

• 5'8 x 22" x 2.5"


• 36.7 Cubic Litres


• FCS Fins


• 1-4 foot surf

Learn More

Just like the name says this Lost surfboard is a bottom feeder it loves the slop surf. This surfboard is a tri-plane hull that catches the smallest of ripple and allows you to turn without losing speed.

Lost Bottom Feeder Details:

• 6' x 22.5"" x 2.75"


• 42.49 Cubic Litres


• Futures 5 fin Setup


• Knee-Head High Waves

Learn More

Knowledge of your past to create a better future. The 1980’s, an era of functional, full volume boards with bright colors and a flashy, fun attitude that made summertime small wave ripping a piece of cake. That was the inspiration for this board. Taking design (both shape and art) direction from some of the hottest boards of the neon 80’s (McCoy, MR, Simon, Stussy, McElroy, Schroff and Rusty). By morphing together what I loved most about this era with a bit of what we have learned in modern times we came up with this “Blast from The Past”. The primary components are a low overall rocker, thickness generously distributed well into the nose and tail (and out into the rails), a conservative bottom with slight Vee in the nose to flat through the middle and slight double concave Vee out the tail. The extremely wide back half of theboard generates radical drive and lift, while the double bump “butt” tail adds control and smooth roll in and out of turns. Works great as quad or thruster so we stock with 5 fin plugs. This board is just too easy to have fun on.

Lost Flashback Surfboard Details:

• 6' x 20.5" x 2.5"


• 34.88 Cubic Litres


• FCS Fins (not included)


• 2-5ft Surf

Learn More

Knowledge of your past to create a better future. The 1980’s, an era of functional, full volume boards with bright colors and a flashy, fun attitude that made summertime small wave ripping a piece of cake. That was the inspiration for this board. Taking design (both shape and art) direction from some of the hottest boards of the neon 80’s (McCoy, MR, Simon, Stussy, McElroy, Schroff and Rusty). By morphing together what I loved most about this era with a bit of what we have learned in modern times we came up with this “Blast from The Past”. The primary components are a low overall rocker, thickness generously distributed well into the nose and tail (and out into the rails), a conservative bottom with slight Vee in the nose to flat through the middle and slight double concave Vee out the tail. The extremely wide back half of theboard generates radical drive and lift, while the double bump “butt” tail adds control and smooth roll in and out of turns. Works great as quad or thruster so we stock with 5 fin plugs. This board is just too easy to have fun on.

Lost Flashback Surfboard Details:

• 5'10 x 20" x 2.38"


• 31.94 Cubic Litres


• FCS Fins (not included)


• 2-5ft Surf

Learn More

The world's all-time best selling fish model surfboard. During the filming of 5'5" REDUX, the RNF and RNF Quad were updated and fine tuned. The nose has gotten wider again, and more conservative overall rocker and less concave make for a board that will hold speed in flats and produce harder, longer carves.

A longer, less pronounced vee in the tail gives a more predictable feel out of turns, and a straighter outline adds drive and hold. The deep wing, influenced by MR's vintage twin fins, adds more control of high speeds and better bite in snaps and out of carves. It still paddles great, still makes you look good, but the updates allow harder, more powerful carving turns and a wider range of performance in more varied surf.

Enjoy playing with a multitude of fin setups. The RNF is designed as a twin with rear trailer, but works great as a pure twin fin or try all three standard thrusters for different feels in different conditions. ...Everyone should own one.

Lost Round Nose Fish Surfboard Details:

• 5'5 x 19.25" x 2.25"


• 27.38 Cubic Litres


• FCS 5 Fin setup


• Wave Height 1-6'

Learn More

The world's all-time best selling fish model surfboard. During the filming of 5'5" REDUX, the RNF and RNF Quad were updated and fine tuned. The nose has gotten wider again, and more conservative overall rocker and less concave make for a board that will hold speed in flats and produce harder, longer carves.

A longer, less pronounced vee in the tail gives a more predictable feel out of turns, and a straighter outline adds drive and hold. The deep wing, influenced by MR's vintage twin fins, adds more control of high speeds and better bite in snaps and out of carves. It still paddles great, still makes you look good, but the updates allow harder, more powerful carving turns and a wider range of performance in more varied surf.

Enjoy playing with a multitude of fin setups. The RNF is designed as a twin with rear trailer, but works great as a pure twin fin or try all three standard thrusters for different feels in different conditions. ...Everyone should own one.

Lost Round Nose Fish Surfboard Details:

• 5'11 x 20.13" x 2.44"


• 34.25 Cubic Litres


• FCS 5 Fin Setup


• Red Resin Tint


• Wave Height 1-6'

Learn More

Mush Machine Description:  We've taken the Diamond Fish and added a wide squash tail lowered the rocker and added vee and deep double out the back.

PURPOSE We designed this board for riding very small gutless mush. By giving this board a very low rocker and wide tail allows this board to fly over flat spots. Added vee out the back allows the board to turn in tight spots which makes it a performance machine!!

SIZE GUIDE Order this board 6-9 inches shorter 1 1/2 inches wider and 1/16 - 1/8 inches thinner than your high performance short board. Or 1-3 inches shorter 1/2 inch wider and 1/16 - 1/8 inches thinner then your White Diamond.

Roberts surfboard Details:

• 5'8 x 20.25" x 2 3/8"


• 31.94 Cubic Litres


• Hydroflex (Natural) Epoxy Technology


• Future Fins


• Knee to Shoulder surf

Learn More