In surfboards, everything is balance. Curvy rockers need to balance with straighter outlines and curvy outlines need flatter rockers. These principles became very apparent in the development of the Pelagic. Beginning with a fairly standard RNF template, we added a point at 12” from the tail and carved a reverse, side-cut, outline from there forward, into the wide point just above center. This effectively creates a reversed curve outline between the riders stance. To balance the negative outline curve, we have added a tremendous amount of rail rocker through the center of the board. The final component is very low, straight and fast centerline rocker, which cuts a massively deep concave through the rail rocker.

Lost Pelagic Surfboard Details:
6'6 x 22" x 2.88"
46.42 Cubic Litres
Future 5-Fin
Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

PLEASE NOTE: THIS  MINI DRIVER HAS A BLEM UNDER THE GLASS AT THE NOSE THAT LOOKS LIKE A CREASE. This board has been discounted and is 100% functional the blem is purely cosmetic.

Lost Mini Driver Details:
6'6 x 21.5" x 2.88"
39.35 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.


Lost Mini Driver Details:

6'6 x 21.5" x 2.88"
43.15 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Lost Mini Driver surfboard is a great bigger wave surfboard that can be ridden shorter by a few inches than your traditional shortboard. This board has a slightly flatter rocker with a pulled in tail so it can handle the 2' slop and the macking barrels. Here is details about the surfboard as described by shaper Matt Biolos. Mini Driver – While preparing a quiver for an Indo trip Kolohe asked for “a short, fast (flat rockered) little 5 fin tube rider”. I recommended the Rock-Up, but he felt it had more tail rocker than he liked and wanted something really, really fast that he could take off extremely deep and pump through tubes from way back. We started with a 6’0” Driver, took note of the nose rocker and outline measurements at 4” and 16” back from the tip, then shrunk the board to a 5’8” and lowered the nose rocker at the tip and 12” back till it matched the 4” and 16” from before. We widened the nose until it matched up the same way. This gave us a screaming fast low nose rocker with a forward placed outline, both attributes give tons of drive. We then rounded off the tail, but left the width at 12” the same. This gave us a very clean and elliptical outline that we expected would move free and easy inside the tube. The Mini Driver performed as hoped. Interestingly enough, one of Kolohe’s buddies (Taylor Clark) grabbed it after it came back from Indo and used it in the US Nationals event in Huntington Beach. He surfed it in 2’ slop all the way to a second place finish in the Open Men’s division. The board worked in everything.

Lost Mini Driver Details:

6'6 x 21.5" x 2.88"
39.35 Cubic Liters
Future Fins/5 fin setup
3-7 foot surf Learn More

The Maurice Cole Metro Surfboard combines width and thickness from the old retro fish, but introduces a tow inspired bottom rocker and a very deep concave. More width in the tail creates a larger sweet spot and an accentuated change in curve at the 1 mark loosens the board up. This board replaces all Fish type boards.

This design has a foot in both camps. Stability and float while still maintaining the edgy characteristics of speed and rippability. Evidence that you can occasionally teach an old dog new tricks.

The Metro is easy to turn and will suit surfers that like a retro feel, but want performance from a board. Unlike an old school fish the Metro 3 will sit high on steep fast sections and won’t morph into a shopping trolley style slide when you want to lay a full tilt cutback or carve deep lines into the wave face. Ask and you shall receive. This is no bog monster.

Maurice Cole Metro Surfboard Details:
6'6 x 22" x 2.75"
41.70 Cubic Litres
FCS Fins
1-5FT surf Learn More

The Maurice Cole Pro Tow surfboard is based on the tow series evolution. The design has a deep concave that is punctuated by a sharp rail which in historical terms would have created a board that would go really fast in a straight line. The Protow ushers in a new era of speed and carve surfing with a rail that won’t let go even in the most critical bottom turn scenario.

The Protow pairs perfectly with the metro as the MC 2 board quiver. Width and volume in the right places create a board that quite often floats better than a conventional board 3 or 4 inches longer and facilitates tighter stronger turns with considerably less effort. This board will have you paddling over the grommets but will impress with its performance steep and deep.

Maurice Cole Pro Tow Details:
6'6 x 20" x 2.75"
36.70 Cubic Litres
FCS Fins
2-8FT Surf Learn More

Over the last 20 years of working and testing with the world’s elite surfers, Maurice Cole has continued to design and shape the magic surfboard for surfers from Curren, Occy, Margo and Slater to Taj, Trent and Ross Clarke-Jones. All the curves and rockers are all Original Designs and have been tested extensively for 12 months before releasing into the market.

The ATM is used in kid grommet boards, short boards, semi-guns or the next board up from a short board and in the bigger Indo/Hawaii guns, that are up to 10 foot long. This design has an elite pedigree and can be relied upon to ride in all conditions.

Pro surfers or advanced riders require a design to work in a variety of waves. The ATM can be relied upon for travel, as it will handle anything that Mother Nature throws at it!

Maurice Cole ATM Surfboard Details:
6' x 18.63" x 2.31"
28.60 Cubic Litres
FCS Fins
2-12FT Surf
Learn More

Derived from the Whiplash-TB. The TB-Stepdown is more of an “every-mans” high performance shortboard. Used by many WT and Qualifying Series competitors, because it works equally well in small junk surf. Featuring the Same WL-TB, hyper extended tail rocker (for tight radius arcs off the back foot) but a significantly more relaxed entry rocker, which combined with a wider nose allows for more drive and forward momentum , and stability, with a bigger landing platform from reverse and tweaked airs. A wider hip and tail block is added to the outline in the tail for more lift at low speeds, but the tail width at 12” is relatively the same as the WL- TB. This allows for superior precision and control than most al other “grovel” boards. With the centerline and rail volume is carried farther into the rails….and out to nose and tail the TB-stepdown is designed to be ridden 1-2” shorter than the WLashTB. In the right size, this is a HP shortboard that can be ridden and enjoyed by most surfers.

Lost Taj Burrow Beach Buggy Details:
6'6 x 20" x 2.75"
Futures Fins
37.64 Cubic Litres Learn More

This Lost Sub-Driver Surfboard is a great beach break surfboard that will handle small to mid sized waves. This board has a little more nose rocker and a flatter tail rocker.

Lost Sub Driver Details:
6'6 x 21 x 2.88
42.58 Cubic Litres
Future Fins Learn More

The Lost Lay-Zboy surfboard is both a continuation and a break away from the Bottom Feeder and Plank Genre surfboards. The Lay-Zboy takes these high volume low rocker small wave surfboard designs and brings it to a wider range of surf capabilities. This surfboard uses an eliptical outline influenced by Wayne Lynch & Michael Peterson in the 1970's as well as Dave Parmenter in the 80's and 90's. These eliptical outlines give the Lay-Zboy a very open and forgiving sweet spot and allow the board to be surfed in knee to well overhead waves.

Lost Lay-Zboy details:
6'0 x 21.25" x 2.56"
38.54 cubic litres
Future 5 fin set up
Epoxy Construction with Bamboo Deck Learn More

Derived from the Whiplash-TB. The TB-Stepdown is more of an “every-mans” high performance shortboard. Used by many WT and Qualifying Series competitors, because it works equally well in small junk surf. Featuring the Same WL-TB, hyper extended tail rocker (for tight radius arcs off the back foot) but a significantly more relaxed entry rocker, which combined with a wider nose allows for more drive and forward momentum , and stability, with a bigger landing platform from reverse and tweaked airs. A wider hip and tail block is added to the outline in the tail for more lift at low speeds, but the tail width at 12” is relatively the same as the WL- TB. This allows for superior precision and control than most al other “grovel” boards. With the centerline and rail volume is carried farther into the rails….and out to nose and tail the TB-stepdown is designed to be ridden 1-2” shorter than the WLashTB. In the right size, this is a HP shortboard that can be ridden and enjoyed by most surfers.



Lost Taj Burrow Beach Buggy Details:





6'6 x 20" x 2.75"


FCS Fins


37.84 Cubic Litres Learn More

The Lost Sub Scorcher 2 surfboard is a fresh twist on the extremely popular Sub Scorcher model. The Vee bottom was removed from the last 6" of the tail which increases the rocker by about a 1/4" still keeping the rail line static. As a result the board surfs looser for better vertical and pocket surfing. To keep the board fast with losts of drive Lost straightened the outline in the tail by adding the double wing swallow tail. This is a great everyman's daily average wave shortboard.

THIS SURFBOARD WAS A RETURN. It has been surfed 1 x and has 2 very minor pressure dents on the deck. The price has been dropped. This board also comes with a Astrodeck black traction pad.

Lost Sub Scorcher 2 Details:

6'0x 19.75 x 2.50


32.45 Cubic Litres


Future 5 Fin Setup


2-5 foot surf

Learn More

Designed to be ridden 2-4” longer than you would a Rocket. The low entry rocker, flat deck and tapered rails (with a full forward outline) paddles through crowds and moving water, and catches waves with ease. The pulled in tail, combined with the aggressive tail rocker and a smoother, shallower concave, allows controlled maneuvers at high speeds on chest high to double overhead waves

Board Details:

6'6 x 2.50 x 2.75

FCS Fins

40.70 cL Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'0 x 19.5 x 2.5"


• 30.36 Cubic Litres


• Future Fins

Learn More

The Shred Sled is a fish design tweaked to be an all-round surfing board. It has a smooth connected feeling that is fast and flowing. Although it looks like a small wave board, the Shred Sled will surf waves up to 6ft in all conditions.

The unique outline allows a full plan shape, yet a wide round tail is positioned behind the wing to give plenty of performance and curve to fit into all types of waves. The wing allows a straighter outline in the center of the board, which provides plenty of speed down the line. The foil has plenty of volume, yet it is shaped to allow the board to sit in the wave face creating a very smooth, connected feeling. The wing breaks this connection and water flow to give response and release when you want it.

The rocker is flat in the belly, giving the board flowing speed, yet it kicks late in the nose and a little in the tail. The deep single concave in the front end of the board blends into a double vee out the tail behind the front fins.

Designed to be ridden 4-5 inches shorter and ¾ to 1 inch wider than your performance shortboard

Haydenshapes surfboard details:

• 6'6 x 20.5 x 2.75"


• 37.88 Cubic Litres


• Future Fins

Learn More

The Super Fish II has been updated for 2012 making one of the most popular boards even better. The idea behind the Super Fish design is to offer a board that rides, paddles and catches waves easily regardless of your ability.

The generous outline and smooth rocker makes this board incredibly easy to ride. One of the most notable features of the Super Fish design is the step deck. This gives the board greater buoyancy while maintaining a performance rail profile making the board sensitive and easier to turn.

The new bottom contour features a deep single-to-double concave providing greater speed and acceleration. The tail wings are now more defined creating bite off the bottom and quicker release through turns. The swallowtail is also shallower than before. This adds surface area under your back foot meaning more speed in flatter waves.

FCS plugs are set up in a tri-quad configuration so you can ride it as a thruster or a quad, and our X2 Epoxy technology uses a multi-layered sandwich process that produces a light yet incredibly durable surfboard that’s ideal for travel.

If you're looking for a high volume, easy to ride surfboard that'll increase your wave count then the Super Fish II is the board for you.

7S Super Fish II Surfboard Details:

• 6' x 20.25" x 2 7/16"


• 33.3 Cubic Litres


• FCS Fins (quad Set included)


• Waist to head high surf

Learn More

The Hypto Krypto is the most versatile shape in the Haydenshapes range, enabling it to be ridden in waves from 1ft to 8ft. It paddles like a dream due to the volume and flatter rocker. You ride the Hypto Krypto on the open face, drawing fast, flowing lines with all the speed it provides.

The outline resembles an old school twin fin in the nose, yet pulls into a rounded pin tail which will give you plenty of hold in the bigger stuff, and provide a lot of curve around the back foot. You can use the wider, straighter outline forward on the board to give you speed down the line and the rounded pintail to draw tighter arcs in the pocket.

Although the rocker of the Hypto Krypto is flat, Hayden has snuck in a little extra lift in the entry to add some curve up front; this helps taking off late, or turning in the steeper sections of the wave. The design of the rocker has been focused around speed, and more speed! The Hypto has never been shaped as a quad because it is too fast already, you’ll find yourself making sections down the line that you would never expect to make.

The foil has plenty of volume around the chest and center area of the board, yet it refines out to a thinner, more pinched rail to keep the board connected to the wave. The concave runs from a rolled vee in the entry, to a slight single transitioning into a vee double out the tail, which gives the board great speed and control from rail to rail.

Overall the Hypto Krypto is the one stop board that you can travel all around the world having fun in average conditions, as well as taking to the barrel and open face when the swell pumps!

Haydenshapes surfboard details:

• 6'0 x 20.25 x 2.75"


• 36.56 Cubic Litres


• Future Fins

Learn More

This M.R. {uffer Fish surfboard is a great high performance fish surfboard that goes from a single to a double concave. This is a great board for everyday average size surf.

M.R. Puffer Fish Details:

6' x 21" 2.5"
FCS Fins (not included)
2-6 foot surf Learn More